The P2795: Gear Shift Direction Circuit High code indicates that there is a higher-than-expected voltage present in the gear shift direction circuit. This issue could be caused by faulty wiring, a short to power, or a malfunction in the control module. The gear shift direction circuit is essential for determining the correct movement of the gear shifter, and a high voltage condition can lead to improper or erratic shifting.
P2795 – Quick Overview
| Code | Information |
|---|---|
| Meaning | P2795: Gear Shift Direction Circuit High |
| Is it serious? | Yes, high voltage in this circuit can cause improper gear engagement or erratic shifting, potentially resulting in safety concerns and affecting drivability. |
| Possible causes | – High voltage in gear shift direction circuit – Faulty circuit or wiring – Control module issues |
| How to diagnose? | – Measure voltage in the gear shift direction circuit – Inspect wiring and connectors – Check for shorts or damage – Replace components as needed |
P2795 Meaning
The P2795: Gear Shift Direction Circuit High code indicates that the voltage in the gear shift direction circuit is above the expected level. This can be due to a short to power, damaged wiring, or a malfunctioning gear shift direction sensor or control module. Excessive voltage can interfere with the system’s ability to control gear shifts properly, causing erratic or delayed shifting behavior.
Step-by-step diagnostic guide
| Action | Description | Tools Needed |
|---|---|---|
| Check for Other Codes | Use an OBD-II scanner to determine if there are additional related codes. Other codes may help pinpoint if there are related issues affecting the transmission or electrical system that could be contributing to the high voltage in the gear shift direction circuit. | OBD-II Scanner |
| Measure Voltage in Gear Shift Direction Circuit | Use a multimeter to measure the voltage in the gear shift direction circuit. Compare the measured value to the manufacturer’s specifications to determine if it is above the recommended level. If the voltage is too high, it indicates a possible short or other circuit problem. | Multimeter, Manufacturer Specifications |
| Inspect Wiring and Connectors | Inspect the wiring and connectors that are part of the gear shift direction circuit. Look for any signs of damaged or exposed wiring, loose connections, or corroded terminals. Faulty connections or damaged insulation can lead to unintended shorts to power, causing elevated voltage. | Flashlight, Safety Gloves |
| Check for Shorts to Power | Use a multimeter to check for shorts to power in the gear shift direction circuit. A short to power in the circuit could lead to high voltage conditions. Carefully trace the wiring to identify any areas where it may be coming into contact with a power source. Repair or replace any faulty wiring as necessary. | Multimeter |
| Test the Gear Shift Direction Sensor or Switch | If applicable, test the gear shift direction sensor or switch using a multimeter. Verify that the sensor outputs are consistent with the manufacturer’s specifications. A malfunctioning sensor may output higher voltage than expected, indicating the need for replacement. | Multimeter, Manufacturer Specifications |
| Verify Control Module Functionality | Use a diagnostic tool to ensure that the transmission control module (TCM) is correctly receiving and processing signals from the gear shift direction circuit. Faults within the control module could cause it to incorrectly interpret signals, leading to a high voltage issue. | Diagnostic Tool, Manufacturer Software |
| Check for Electrical Interference | Inspect the circuit for any sources of electrical interference or noise that might be contributing to erratic voltage readings. Electrical noise can cause improper signal transmission. If needed, shield or reroute the wiring to minimize interference. | Oscilloscope, Diagnostic Tool |
| Inspect Grounding | Ensure that all grounding points related to the gear shift direction circuit are properly connected and free from corrosion. Improper grounding can cause issues with voltage regulation and result in elevated voltage. Clean and tighten any loose grounds to maintain circuit stability. | Multimeter, Wire Brush |
| Replace Faulty Components as Needed | Replace any components found to be faulty during diagnostics, including sensors, wiring, or the control module. Ensure that any replacements meet the manufacturer’s specifications for proper function. | Replacement Gear Shift Direction Sensor, Wiring Repair Kit, Control Module |
| Clear the Code and Test Drive | After repairs, use an OBD-II scanner to clear the P2795 code. Conduct a test drive to monitor the performance of the gear shift system, ensuring there are no further high voltage issues and that gear selection is smooth and accurate. | OBD-II Scanner |
| Recheck for Codes | Perform a final scan to confirm that the P2795 code has not returned. If the code persists, further diagnostics may be required to identify the ongoing issue causing high voltage in the gear shift direction circuit. | OBD-II Scanner |
Free PDF: How to choose OBD2 scanner
I’ve made you a free PDF to choose the OBD2 scanner in 5 minutes.
✅ Which OBD2 scanner is best?
✅ Which type should you get (DIY, Pro, Hobby)
✅ What is the best scanner for the exact brand/feature (e.g best for BMW)
✅ How to get a Bi-Directional tool for as cheap as $40
✅ Discount coupons for scanners
PDF is 100% free and it is designed to help you pick a scanner in less than a few minutes! Not a boring 50-page guide.
Just tell me where to send it.
